Home     /     Blog     /     Selecting an AKD Emulsifier: Compatibility and Stability Questions
By Coco

Selecting an AKD emulsifier requires compatibility work across wax, water, polymer, charge conditions, homogenization, storage and the paper machine wet end. “High polymer emulsifier” is a functional trade description, not a universal formula. Buyers should compare technical fit, reproducible emulsion quality and cost in use before comparing manufacturer, factory, exporter or supplier prices.

The following questions organize laboratory screening, emulsion testing, mill trials and supplier documentation without assuming that one composition or dosage fits every AKD process.

Confirm the emulsifier identity and supplied form

Ask the supplier to state the commercial grade, chemistry description, ionic character, active solids, viscosity basis, pH, density, solvent or carrier, storage limits, shelf life and manufacturing site. The quotation, TDS, SDS, sample label, COA and purchase order should refer to the same material.

Do not infer composition from the trade name

A polymeric emulsifier may be used alone or with cationic starch, protective colloids, surfactants or other stabilizing components. Patent literature describes multiple possible AKD sizing formulations and emphasizes that emulsion stability is a formulation issue. A cited formulation is not automatically the composition of a River Chem product. Source: US6159339A, Paper size and paper sizing process.

Match the emulsifier to the AKD wax

Record AKD grade, melt behavior, supplier, storage history and any relevant composition information. Screen the emulsifier with the actual wax rather than a convenient substitute. Define wax-to-emulsifier ratio on an active basis, water quality, temperature profile, premix sequence, homogenizer pressure or shear, number of passes and cooling conditions.

AKD grade names such as 1840 and 1865 are supplier-defined and should not be treated as universal chemical specifications. When wax source or grade changes, repeat a justified compatibility check rather than assuming the approved emulsifier conditions remain valid.

Control process water and charge conditions

Measure water hardness, conductivity, pH, temperature and microbiological condition where relevant. Review interaction with starch, fixatives, retention aids, alum, fillers, dyes and process contaminants. Charge balance can affect droplet stabilization and retention, but a higher cationic value is not automatically better for every furnish.

Define the make-down window

Document minimum and maximum temperatures, concentration, mixing time, shear, dilution sequence and hold time. Identify which deviations create coarse particles, foam, excessive viscosity, deposits or phase separation. The procedure must be practical for the plant’s pumps, heat exchange, homogenizer and instrumentation.

Measure emulsion quality immediately

Agree on tests and acceptance criteria before the trial. Depending on the process, these can include solids, particle-size distribution, viscosity, pH, charge-related measurements, appearance, sediment, creaming, foam and filtration behavior. Sample location and time after manufacture should be fixed because an emulsion can change during transfer and storage.

TAPPI’s overview of AKD sizing describes emulsification, prevention of particle agglomeration, retention on solid surfaces, spreading and curing as interconnected steps. This supports evaluating the complete process instead of approving an emulsifier from one bench-top observation. Source: TAPPI Journal, AKD sizing under simplified treatment conditions.

Run a defined stability study

Stability should be evaluated for the actual intended hold time and temperature. Inspect and measure at agreed intervals. Avoid relying only on a visual check at room temperature. Where appropriate, assess particle-size drift, viscosity, pH, separation, sediment, filtration and retained sizing performance after storage.

Stress tests need a purpose

Heat, cold, centrifugation or accelerated ageing can be useful for comparative screening, but they do not automatically predict shelf life. Define what failure mode the stress test represents and correlate it with normal storage data before turning it into a purchasing specification.

TAPPI’s work on AKD reaction kinetics reports that emulsion stability can be adversely affected by temperature, dilution, elevated pH and accelerators, and that hydrolysis produces inactive ketone. Buyers should use the exact mill conditions and supplier guidance when designing tests. Source: TAPPI, Practical Aspects of Alkaline Sizing—AKD reactions and hydrolysis.

Connect stability to paper performance

A physically stable emulsion must still deliver sizing and machine cleanliness. Plan a mill trial with baseline and controlled dosage steps. Track Cobb or another approved sizing test, size development over time, cure conditions, AKD retention, deposits, foam, drainage, formation, press performance, dryer conditions and converting behavior.

  • Sizing response: compare conditioned sheets using the same test method and timing.
  • Runnability: monitor deposits, breaks, felts, wires and white-water changes.
  • Efficiency: calculate emulsifier and AKD consumption per saleable ton.
  • Robustness: repeat across representative furnish and operating conditions.

Review the batch specification

The COA should identify product, grade, manufacturing source, batch, dates, specification revision, methods, limits, actual results, units and release authorization. Discuss active-solids method, viscosity conditions, pH basis and any relevant charge or residual-monomer control. A generic brochure is not a batch-specific result.

Illustrative white-background IBC image associated with AKD high polymer emulsifier
Illustrative IBC image. It does not establish the current AKD emulsifier chemistry, active solids, package, label, inventory or batch specification.

Supplier compatibility questions

  1. Which AKD wax grades and emulsion processes have been evaluated?
  2. What active-basis ratio and operating window are recommended for screening?
  3. Which water-quality and charge conditions can reduce stability?
  4. Which immediate and aged-emulsion tests should be used?
  5. How should hold time, temperature and dilution be controlled?
  6. Which manufacturing, raw-material, method or packaging changes trigger notice?
  7. Can representative COAs, TDS, SDS and technical trial support be supplied?

Compare price through cost in use

Normalize quotations to the same active-solids basis and include freight, package, storage, make-down energy, dilution water, cleaning, waste and technical service. Credit only sizing efficiency and productivity improvements demonstrated in the controlled trial. A lower price per drum can be offset by higher dosage, short hold time, deposits or lost AKD efficiency.

Request AKD emulsifier documentation

Review River Chem’s AKD High Polymer Emulsifier page and the broader Paper Making Chemicals range. To request available specifications, SDS, sample options, price and a quotation, contact Rriver Chemical with the AKD wax, emulsification equipment, water conditions, trial quantity, packaging and destination.

  • Get Best Chemical

    Join Rriver Chemical Newsletter to get more information of chemical products, and all kinds of chemical products.

  • Subscribe to Our Blog

    We will never rent or sell your email to anyone.

  • Develop Your Chemical Business with Rriver Chemical

    Contact Us Now